Type 304 stainless steel is the right choice for most food contact equipment handling dry products, beverages and mild foods. Type 316L is worth the extra cost when equipment meets salt, acids, chlorides or aggressive cleaning chemicals, because its molybdenum content gives much better resistance to pitting and crevice corrosion. The “L” adds value wherever there is significant welding, such as tanks and piping.

What’s the Difference?

Both are austenitic stainless steels, the family used for nearly all food processing equipment. The key differences are in their alloy content:

Element304316 / 316L
ChromiumAbout 18%About 16–18%
NickelAbout 8%About 10–14%
MolybdenumNoneAbout 2–3%
Carbon (standard grade)0.08% max0.08% max
Carbon (“L” grade)0.03% max (304L)0.03% max (316L)

Chromium forms the thin, invisible oxide layer that makes stainless steel “stainless.” Molybdenum strengthens that protection against chlorides, which is where 316 earns its place.

What the “L” Means and Why It Matters for Welded Equipment

“L” stands for low carbon. When standard-carbon stainless steel is welded, the heat can cause chromium to combine with carbon near the weld, leaving areas with less corrosion resistance. Keeping carbon at 0.03% or below greatly reduces this risk.

For heavily welded equipment such as tanks, vessels, kettles and sanitary piping, specifying 304L or 316L protects corrosion resistance at the welds, where problems usually start. Good welding practice matters too: matching filler metal, controlled heat input, back-purging with argon on tube and pipe welds, and proper post-weld cleaning and passivation. Automated orbital TIG welding is widely used on sanitary tubing for consistent, smooth internal welds.

When 304 Is Enough

304 (or 304L) is the cost-effective standard for:

  • Dry products: flour, sugar, grains, dried spices, powders and snacks
  • Mixers, conveyors, sifters and hoppers handling dry ingredients
  • Many beverages and mild liquids at moderate temperatures
  • Frames, guards, covers and other non-contact parts

For example, a ribbon blender for dry spice blends or flour premixes is commonly built in 304.

When to Choose 316L

Specify 316L when equipment will see:

  • Salt and brines: pickles, brined vegetables, cheese brines, cured meats
  • Acidic products: tomato products, ketchup, fruit juices and pulps, vinegar-based sauces
  • Chlorides from cleaning: chlorinated sanitizers or frequent aggressive cleaning
  • Seafood and salty environments, including coastal plants
  • High temperatures combined with any of the above, which speeds up corrosion
  • Pharmaceutical or high-purity applications where customers expect 316L

Stainless steel tanks for sauces, juices and brines are typical candidates for 316L, at least on product-contact surfaces.

Cost and Mixed-Grade Designs

316L costs more than 304 because of its higher nickel and added molybdenum, and the price gap moves with metal markets. A practical way to control cost is a mixed-grade design: 316L for product-contact parts that face corrosive conditions, and 304 for frames, covers and non-contact structure. Make sure your specification states clearly which parts are which grade.

Surface Finish Matters as Much as Grade

A rough or poorly finished surface can trap product and bacteria and corrode faster, whichever grade you choose. For sanitary product-contact surfaces, buyers commonly specify a maximum roughness of around 32 µin Ra (0.8 µm), with smoother finishes for dairy, pharma or sticky products. Welds should be ground flush and polished where they touch the product.

Kosmo offers stainless steel polishing for fabricated equipment.

How to Verify What You’re Getting

You can’t tell 304 from 316 by looking at it, and a magnet test isn’t reliable: both are generally non-magnetic, but cold-worked areas of either can become slightly magnetic. To verify the grade:

  • Ask for mill test certificates for sheet, plate and tube, showing chemical composition and traceability
  • Request positive material identification (PMI) using a handheld analyzer during the factory acceptance test, especially for critical 316L parts
  • Put the grade in your purchase specification for each component, not just “stainless steel”

These checks matter most when buying from a new supplier or importing equipment.

Frequently Asked Questions

Is 304 stainless steel food safe?

Yes. 304 is the most widely used stainless steel for food contact equipment. It’s suitable for most foods unless the equipment faces significant salt, acids or chlorides.

Is 316L always better than 304?

It has better corrosion resistance, but it isn’t always necessary. For dry products and mild conditions, 304 performs well at lower cost.

Do I need the “L” grade?

For equipment with a lot of welding, such as tanks and piping, low-carbon grades are the safer choice because they protect corrosion resistance at the welds.

Can a magnet tell me if steel is 304 or 316?

No. Both are typically non-magnetic, and either can become slightly magnetic after cold working. Use mill certificates and PMI testing instead.

Does the FDA require a specific stainless steel grade?

FDA current good manufacturing practice rules require food contact surfaces to be corrosion-resistant, nontoxic and cleanable, but they don’t name a specific grade. 304 and 316L are both widely accepted for food contact.

Building Equipment in 304 or 316L

Kosmo Engineering fabricates food processing machinery and tanks in SS304 and SS316L, with TIG and orbital welding and polishing in-house. Visit our page for US manufacturers to see how we work with US buyers, or send us your specification.

Leave a comment

error: Content is protected !!